Page 3 sur 8 PremièrePremière 12345 ... DernièreDernière
Résultats de 21 à 30 sur 75
  1. #21
    Membre enregistré Membre Habitué
    Inscrit
    16/09/2015
    Localisation
    Italie
    Messages
    32
    Véhicule
    Peugeot 208 GTi BPS Rouge Rubis
    Mentionné
    6 Post(s)
    Taggué
    Sujet(s)
    probably every ECU revision use different addresses and PID codes: the ecu on my car is the MEVD17.4.4.
    If you have still access to the diagobox tool, you can easily discover the address+custom PID for every parameter:
    you must connect the diagobox tool and the ELM327 dongle together to the OBD port, put the ELM327 in "listening mode" and, on the diagbox, select to measure only one parameter at a time (using the dedicated menu)
    Let me know if you need other infos about that...

  2. #22
    Membre enregistré Membre Habitué
    Inscrit
    16/09/2015
    Localisation
    Italie
    Messages
    32
    Véhicule
    Peugeot 208 GTi BPS Rouge Rubis
    Mentionné
    6 Post(s)
    Taggué
    Sujet(s)
    Citation Envoyé par darkjojo78 Voir le message
    does not work for my ecu .

    i found an application on android runs with the chip elm327 and offers functions that approaches the diagbox without the telemetry
    https://play.google.com/store/apps/d....faplite&hl=fr

    Fichier joint 15491
    I didn't know this app: I will test it, analyzing the data traffic on the CAN bus, to see if the app uses custom PSA PIDs or the classical OBDII PIDs.

  3. #23
    Membre enregistré Routard Avatar de darkjojo78
    Inscrit
    09/03/2015
    Localisation
    78 Yvelines
    Messages
    1 313
    Véhicule
    Peugeot 208 GTi Blanche Perle Nacrée
    Kilométrage
    84000
    Mentionné
    115 Post(s)
    Taggué
    Sujet(s)
    Citation Envoyé par mfc Voir le message
    probably every ECU revision use different addresses and PID codes: the ecu on my car is the MEVD17.4.4.
    If you have still access to the diagobox tool, you can easily discover the address+custom PID for every parameter:
    you must connect the diagobox tool and the ELM327 dongle together to the OBD port, put the ELM327 in "listening mode" and, on the diagbox, select to measure only one parameter at a time (using the dedicated menu)
    Let me know if you need other infos about that...

    how to connect the box elm327 and the diagbox together on the same socket obd

  4. #24
    Membre enregistré Membre Habitué
    Inscrit
    16/09/2015
    Localisation
    Italie
    Messages
    32
    Véhicule
    Peugeot 208 GTi BPS Rouge Rubis
    Mentionné
    6 Post(s)
    Taggué
    Sujet(s)
    Citation Envoyé par darkjojo78 Voir le message
    how to connect the box elm327 and the diagbox together on the same socket obd
    the easiest way is to buy a OBDII "Y" or "splitter" cable with 1 male and 2 females connectors

  5. #25
    Membre enregistré Routard Avatar de darkjojo78
    Inscrit
    09/03/2015
    Localisation
    78 Yvelines
    Messages
    1 313
    Véhicule
    Peugeot 208 GTi Blanche Perle Nacrée
    Kilométrage
    84000
    Mentionné
    115 Post(s)
    Taggué
    Sujet(s)
    I did not know that it exists, otherwise can you explain to me a little more the setting to do on the diagbox with the elm327


    Nom : 61vMK-0U+qL._AC_SX679_.jpg
Affichages : 688
Taille : 32.2 Ko

  6. #26
    Membre enregistré Membre Habitué
    Inscrit
    16/09/2015
    Localisation
    Italie
    Messages
    32
    Véhicule
    Peugeot 208 GTi BPS Rouge Rubis
    Mentionné
    6 Post(s)
    Taggué
    Sujet(s)
    as I had already written in a previous post, to enable the listening mode:
    AT H1
    AT D1
    AT CAF0

    to listen all the messages from the 6xx addresses:
    AT MR 06

    to listen all the messages from the 4xx addresses:
    AT MR 04

    to listen a specific message address (e.i. 0x488):
    AT CF 488
    AT CM FFF

    on the diagbox tools, there is a menu like "personalized parameter reading" in which you can select which value to read continuously
    if you need it, tomorrow, I can send you a screen shot of this menu...
    Dernière édition par mfc; 29/09/2019 à 23:39

  7. #27
    Membre enregistré Routard Avatar de darkjojo78
    Inscrit
    09/03/2015
    Localisation
    78 Yvelines
    Messages
    1 313
    Véhicule
    Peugeot 208 GTi Blanche Perle Nacrée
    Kilométrage
    84000
    Mentionné
    115 Post(s)
    Taggué
    Sujet(s)
    Citation Envoyé par mfc Voir le message
    as I had already written in a previous post, to enable the listening mode:
    AT H1
    AT D1
    AT CAF0

    to listen all the messages from the 6xx addresses:
    AT MR 06

    to listen all the messages from the 4xx addresses:
    AT MR 04

    to listen a specific message address (e.i. 0x488):
    AT CF 488
    AT CM FFF

    on the diagbox tools, there is a menu like "personalized parameter reading" in which you can select which value to read continuously
    if you need it, tomorrow, I can send you a screen shot of this menu...
    I received my cable today, to connect the diagbox and the elm327. I made custom measurements with the diagbox and monitor the bus can with elm327 on the engine calculator. Diagbox uses the 6A8 header for engine calculator

    regime moteur / engine rpm
    6A8 5 04 21 C0 80 01

    température calculateur/ calculator temperature
    6A8 5 04 21 CB 80 01

    température air extérieur / outside air temperature
    6A8 5 04 21 C2 80 01

    température eau / water temperature
    6A8 5 04 21 C0 80 01

    température huile / oil temperature
    6A8 5 04 21 C2 80 01

    position pédale accélérateur / accelerator pedal position
    6A8 5 04 21 CA 80 01


    Dernière édition par darkjojo78; 05/05/2020 à 19:02

  8. #28
    Membre enregistré Routard Avatar de darkjojo78
    Inscrit
    09/03/2015
    Localisation
    78 Yvelines
    Messages
    1 313
    Véhicule
    Peugeot 208 GTi Blanche Perle Nacrée
    Kilométrage
    84000
    Mentionné
    115 Post(s)
    Taggué
    Sujet(s)
    on décortique la ligne de commande custom init
    at sp 6 pour la sélection du protocole iso 15765-4 can (11 bit id, 500 kbaud)
    at sh 6a8 pour sélection de l'en-tête
    at fc sd 30 00 00 flow control set data
    at fc sm 1 flow control set mode
    at cra 688 set the can rx addr
    81 pour se connecter au calculateur moteur
    10c0

    après essai sa fonctionne pas, mais j'ai peut être trouves le problème qui viendrait de la commande at fc sd 30 00 00. Sur ma 208 avec le diagbox il envoi la commande 6a8 30 00 05, je vais remplacer le 30 00 00 par 30 00 05


    nouvelle custom init
    atsp6\natsh6a8\natfcsh6a8\natfcsd300005\natfcsm1\n atcra688\n81\n10c0


    Dernière édition par darkjojo78; 05/05/2020 à 19:15

  9. #29
    Membre enregistré Routard Avatar de darkjojo78
    Inscrit
    09/03/2015
    Localisation
    78 Yvelines
    Messages
    1 313
    Véhicule
    Peugeot 208 GTi Blanche Perle Nacrée
    Kilométrage
    84000
    Mentionné
    115 Post(s)
    Taggué
    Sujet(s)
    1- on lance le scan de tous les calculateur sur le diagbox

    Nom : scan tous les calculateur.PNG
Affichages : 796
Taille : 51.9 Ko


    2- on se connecte au calculateur MEVD17.4.2

    Nom : connecter au calculateur moteur.PNG
Affichages : 759
Taille : 52.6 Ko


    3- on lance une mesure personnaliser

    Nom : demande mesure personaliser.PNG
Affichages : 815
Taille : 53.4 Ko


    on retrouve bien les ligne
    6A8 01 81
    6A8 30 00 05
    6A8 04 21 C0 80 01
    avec les en-tête 6A8 et 688
    Dernière édition par darkjojo78; 08/10/2019 à 17:08

  10. #30
    Membre enregistré La 208 GTi c'est votre vie ! Avatar de Hugo
    Inscrit
    02/01/2017
    Localisation
    Vosges, Meurthe-et-Moselle
    Messages
    3 310
    Véhicule
    Peugeot 208 GTi Blanche Perle Nacrée
    Kilométrage
    40 000
    Mentionné
    274 Post(s)
    Taggué
    Sujet(s)
    Super travail, j'ai hâte de voir la suite !
    208 GT 1.2 THP 170ch stage 3

Page 3 sur 8 PremièrePremière 12345 ... DernièreDernière

Liens sociaux

Règles des messages

  • Vous ne pouvez pas créer de sujets
  • Vous ne pouvez pas répondre aux sujets
  • Vous ne pouvez pas importer de fichiers joints
  • Vous ne pouvez pas éditer vos messages
  •  
  • Les BB codes sont Activés
  • Les Smileys sont Activés
  • Le BB code [IMG] est Activé
  • Le code [VIDEO] est Activé
  • Le code HTML est Désactivé
A Propos de nous
Forum 208 GTi : Le premier site sur la Peugeot 208 GTi.
Ce site est indépendant de la société Automobiles Peugeot, dépositaire de la marque Peugeot.
Le Forum sur les réseaux sociaux