Rechercher:

Type: Messages; Utilisateur: mfc

Page 1 sur 2 1 2

Rechercher: La recherche a pris 0.02 secondes ; générée il y a 10 minute(s).

  1. darkjojo78 add the following PID to your list: ...

    darkjojo78 add the following PID to your list:

    Suralimentation et injection direct:
    Tension de la batterie de servitude
    6A8 03 22 D7 8A
    688 05 62 D7 8A xx xx
    data scaling unknown

    Consigne...
  2. Because your car use a MEDV17.4.2 ecu, you need...

    Because your car use a MEDV17.4.2 ecu, you need this document which contain all the infos you need:
    Funktionsrahmen MED17.4.2 PSA FRM_14-446.984_I12.1_1_EN.pdf

    Marco
  3. Dear darkjojo78, very good job!

    Dear darkjojo78,
    very good job!
  4. The 6A8 address is used to request data and 688...

    The 6A8 address is used to request data and 688 is the reply (like on my car).

    the data request command is:
    6A8 04 21 C0 80 01

    because the reply start with 688 10 ... the EC tell you that the...
  5. for completeness of information. the message...

    for completeness of information.
    the message with 0x488 address is sent 10 times per second and is composed by 8 byte of data with the following meaning (at least for the MEVD17.4.4 ECU):
    Byte 1:...
  6. thi is the electrical connection of the probe to...

    thi is the electrical connection of the probe to the ecu MEVD17.4.4
  7. yes is a resistance probe, but you note that:...

    yes is a resistance probe, but you note that:
    "The engine oil level sensor is only active when the vehicle contact is switched on and is deactivated when the engine is started."
    the resistance...
  8. as I had already written in a previous post, to...

    as I had already written in a previous post, to enable the listening mode:
    AT H1
    AT D1
    AT CAF0

    to listen all the messages from the 6xx addresses:
    AT MR 06

    to listen all the messages from...
  9. You are right in saying that the oil level sensor...

    You are right in saying that the oil level sensor is also the oil temperature sensor; according to the official PSA documentation for the EP6FDTX engine, the oil level sensor (P/N:9806246080) has 3...
  10. The 208 GTi BPS (208ch euro6) does not have the...

    The 208 GTi BPS (208ch euro6) does not have the oil temperature sensor.
    There are only the oil pressure sensor and oil level sensor.
    The oil temperature is only calculated by engine ECU and sent to...
  11. the easiest way is to buy a OBDII "Y" or...

    the easiest way is to buy a OBDII "Y" or "splitter" cable with 1 male and 2 females connectors
  12. I didn't know this app: I will test it, analyzing...

    I didn't know this app: I will test it, analyzing the data traffic on the CAN bus, to see if the app uses custom PSA PIDs or the classical OBDII PIDs.
  13. probably every ECU revision use different...

    probably every ECU revision use different addresses and PID codes: the ecu on my car is the MEVD17.4.4.
    If you have still access to the diagobox tool, you can easily discover the address+custom PID...
  14. since the address is different, I doubt that your...

    since the address is different, I doubt that your car uses the same codes as my car.
    However, try these 2 codes, if they work I'll send you all the others:

    engine RPM:
    query: 03 22 D4 00
    reply:...
  15. Try this command sequence for the ELM327: AT H1...

    Try this command sequence for the ELM327:
    AT H1
    AT D1
    AT CAF0
    try to listen all the messages from the 6xx addresses:
    AT MR 06

    you should get results even when the engine is off...
  16. I confirm that the standard PIDs reported by...

    I confirm that the standard PIDs reported by darkjojo78 are supported by our 208 GTi plus the following:
    13 Oxygen sensors present
    15 lambda sensor 2 (Narrow band - post cat)
    1C OBD standard ...
  17. the header 6A8 is right, but it is not usable by...

    the header 6A8 is right, but it is not usable by the Torque App because it is not standard (it is specific of Peugeot)...
  18. MEVD17.4.4 Ecu

    Hi,
    Someone has informations to exchange (map locations, firmware, etc...) about the MEVD17.4.4 ecu of our 208 GTi?

    Thanks
  19. Dear Laur'nt, are DS.UNO pads noisy in road...

    Dear Laur'nt,
    are DS.UNO pads noisy in road use/ligh t braking?

    Thanks

    Marco
  20. On a turbocharged engine, any restriction on the...

    On a turbocharged engine, any restriction on the inlet and on the exhaust reduces the engine efficiency:
    if the engine breathes better it produces the same power with less fuel consumption, or...
  21. I use the CFD module of the Comsol software. the...

    I use the CFD module of the Comsol software.
    the design of the airscoop internal volume only is needed to do the simulation.

    Marco
  22. Dear Hugo, if you want, reply me in French;...

    Dear Hugo,
    if you want, reply me in French; there is no problem. ;)
    The purpose of the CFD simulation is to evaluate if the benefit of having cooler air is greater than the disadvantage due to...
  23. Dear Hugo, congratulations for your excellent...

    Dear Hugo,
    congratulations for your excellent work!

    did you do any CFD simulation to find the pressure drop caused by your airscoop?
    having the original 3d design is easy to do the...
  24. Yes, the update involve only the firmware on the...

    Yes, the update involve only the firmware on the ECU, not the SMEG, all the EEPROM of the ECU is erased and the rewritten using the DiagBox software through the OBDII connector.
    I asked the...
  25. ECU firmware update

    Hi,
    recently, I have carried out the annual maintenance of the car: the mechanic has also updated the ECU firmware of my 208 GTI BPS with a new version released by Peugeot probably in November 2017....
Résultats de 1 à 25 sur 32
Page 1 sur 2 1 2
A Propos de nous
Forum 208 GTi : Le premier site sur la Peugeot 208 GTi.
Ce site est indépendant de la société Automobiles Peugeot, dépositaire de la marque Peugeot.
Le Forum sur les réseaux sociaux